Use the button above or message us on WhatsApp for a quote, technical documentation, or engineering support on the VS01A-46T.
Adding tilt to a wall mount means introducing a pivot point, and every pivot point is a place where a rigid bracket would otherwise resist load without deflecting. The VS01A-46T compensates by doubling its standoff profile against the fixed VS01A-46F, 60mm versus 30mm, giving the tilt hardware enough structural depth to carry the same 80kg rating through a full +10/-10 degree range without the panel drifting out of position under its own weight once angled.
The panel locks mechanically at whatever angle it’s set to. It isn’t a friction hinge that needs constant tension, it’s a toolless mechanical stop system within that +10/-10 window, adjustable after the display is already hung and cabled. Every unit is strength-tested to four times its rated 80kg capacity, the same testing standard applied across the rest of the VSYS fixed and tilt range.
Specify the VS01A-46T over the fixed VS01A-46F wherever the final mounting height sits above typical eye level and the room brief calls for angle correction after the panel goes up: reception desks, above standard-height cabinetry, and secondary displays in tiered-seating rooms where sightlines vary by seat. The 80kg class puts it in the same large-format bracket as the fixed model, so it also suits control-room and command-center displays where a downward correction angle matters more than a fixed sightline.
Where the mount height is already at eye level and won’t need correction, the fixed VS01A-46F is the simpler, lower-part-count choice for the same weight class.
Wall fixing options match the fixed-mount range: solid wall or double-stud at 406mm, 450mm, or 600mm spacing. The base plate installs first and is leveled before the tilting head assembly and panel bracket go on, the same sequencing as a fixed mount, with the tilt adjustment itself being the only step that happens after the panel is already hung and cabled. Given the weight class involved, professional installation is recommended and available UAE-wide on request.
| Product Category | Tilt TV Wall Mount |
| Material | Steel |
| Surface Finish | Powder Coating, Fine Texture Black |
| Dimensions | 60 x 685 x 425mm (2.4″ x 27″ x 16.7″) |
| Fit Screen Size | 37″-86″ |
| Curved Panel Compatible | Yes |
| Mounting Hole Pattern | VESA and Universal |
| Maximum Mounting Hole Spread | 645 x 402mm |
| Weight Capacity | 80kg (176lbs) |
| Strength Test Rating | 4x rated capacity |
| Standoff Profile | 60mm (2.4″) from wall |
| Tilt Range | +10 degrees / -10 degrees, toolless |
| Screen Freely Tilting | Yes |
| Wall Compatibility | Solid wall or double-stud, 406mm / 450mm / 600mm spacing |
| Wall Plate Type | Fixed base, tilting head assembly |
| Panel Attachment | Detachable panel bracket |
| Direction Indicator | Yes |
No. The VS01A-46T holds the same 80kg rating as the fixed VS01A-46F, because its standoff profile is doubled, 60mm versus 30mm, giving the tilt hardware enough structural depth to carry that load through the full +10/-10 degree range without the panel drifting once angled.
It locks mechanically at the set angle within the +10/-10 degree range. It isn’t a friction hinge that needs constant tension or loosens over time, it’s a toolless mechanical stop system that holds position reliably once set, even under the full 80kg rated load.
Yes, tilt adjustment is a toolless post-installation step and doesn’t require detaching the panel from the bracket or disturbing any cabling already run behind the display. The base plate and panel bracket stay fully assembled while the angle is reset.
Up to a 645x402mm maximum hole spread, the same VESA and Universal pattern coverage as the fixed VS01A-46F. This spans the common mounting hole spacings found on 37″-86″ commercial and consumer panels from most major display manufacturers.
Yes. It’s rated for curved panels within the same 37″-86″ screen size and 80kg weight limits as flat panels, with the tilt mechanism functioning identically on either panel type. No separate curved-panel SKU or bracket adapter is required.
Solid wall installation or double-stud mounting at 406mm, 450mm, or 600mm spacing, the same stud-spacing coverage as the fixed VS01A-46F. The base plate installs and levels first, before the tilting head assembly is attached.
Yes. Given the 80kg weight class and the tilt mechanism’s two-stage installation sequencing, base plate first, then tilting head assembly, professional installation is recommended and available UAE-wide on request through the same quote form or WhatsApp.
Tell us about your project and our team will recommend the right mounting solution for your display or video wall installation.
