Use the button above or message us on WhatsApp for a quote, technical documentation, or engineering support on the VSVW02-46T.
The VSVW02-46T is a push-pull video wall mount rated to 45kg for 37″-70″ displays, using a scissor-lift X-linkage that converts a single hand-press into 215mm of straight-line extension off the wall, then locks back to a 68mm profile for normal display. It’s built for video wall and digital signage arrays where individual panels need rear access for cabling or maintenance without dismounting the display or disturbing the panels mounted beside it.
The X-linkage geometry is what makes the pop-out motion straight rather than an arc: as the scissor pairs fold, each pivot point travels along a fixed path perpendicular to the wall plate, so the panel face stays parallel to the wall through the full 68-215mm range instead of tilting forward as it extends. A quick-lock mechanism holds the extended position until deliberately released, and lateral shift brackets on the wall plate allow individual panel alignment within a multi-screen array after installation.
The VSVW02-46T is specified for video wall and digital signage installations where panels sit close together and individual rear access matters: retail digital signage walls, control room video walls, and menu board arrays where cabling or maintenance on one panel shouldn’t require dismounting neighboring panels. The lateral shift and leveling adjustments are what make multi-panel seam alignment achievable on-site rather than requiring perfect wall-plate placement beforehand.
Where the install is a single standalone display rather than part of a tiled array, a standard fixed, tilt, or full-motion VSYS mount is the more appropriate specification, the push-pull mechanism and lateral shift hardware here are built specifically for video wall use.
This model is rated for solid wall installation only, reflecting the concentrated load path through the scissor-lift mechanism at a single wall-plate location. Lateral shift brackets and the leveling adjustment are used after the initial hang to fine-tune each panel’s position relative to its neighbors in the array. For multi-panel builds, connect plates (sold separately) link adjacent wall plates for a longer, more rigid mounting run. Given the precision alignment involved in video wall installs, professional installation is strongly recommended and available UAE-wide on request.
| Product Category | Video Wall Mount |
| Build Class | Standard |
| Material | Steel |
| Metal Sheet Thickness | Wall Plate: 2mm; Bracket Arm: 2.5mm |
| Surface Finish | Powder Coating, Fine Texture Black |
| Dimensions | 760 x 465 x 215mm (29.9″ x 18.3″ x 8.5″) |
| Fit Screen Size | 37″-70″ |
| Mounting Hole Pattern | VESA |
| VESA Compatibility | 200×200, 400×200, 300×300, 400×400, 600×400 |
| Maximum Mounting Hole Spread | 600 x 400mm |
| Weight Capacity (Per Screen) | 45kg (99lbs) |
| Screen Quantity | 1 (connect plates required for multi-panel arrays) |
| Strength Test Rating | 4x rated capacity |
| Extension Range | 68mm to 215mm (2.7″ to 8.5″) from wall |
| Screen Leveling | +3 degrees / -3 degrees |
| Installation | Solid wall only |
| Lateral Adjustment | Yes, lateral shift brackets |
| Anti-Theft | Yes, locking hole (padlock not included) |
| Cable Management | No |
A scissor-lift X-linkage converts a single hand-press into straight-line extension off the wall. As the scissor pairs fold, each pivot travels along a path perpendicular to the wall plate, so the panel face stays parallel to the wall through the full 68-215mm range rather than tilting forward as it extends. A quick-lock holds the extended position until deliberately released.
They let an installer slide an individual panel left or right within a multi-screen array after the wall plate is installed, correcting seam alignment between adjacent panels without redrilling. This is essential for a video wall to read as one continuous surface rather than a grid of visibly misaligned screens.
Yes, but the push-pull mechanism, lateral shift brackets, and anti-theft locking hole are specifically built for tiled video wall and digital signage arrays. For a single display, a standard VSYS fixed, tilt, or full-motion mount is typically the more appropriate and cost-effective specification.
It accepts a separate padlock, not included, to prevent unauthorized removal of the display in public-facing or commercial installations. This is a common requirement for retail signage, transit displays, and other unsupervised public locations where the mount is within physical reach of the public.
Each unit supports one screen, but connect plates, sold separately, link adjacent wall plates together to build longer menu board or video wall runs with multiple panels mounted side by side and sharing a single rigid mounting structure across the full array.
Yes. Given the precision seam alignment required across a multi-panel video wall array, professional installation is strongly recommended and available UAE-wide on request through the same quote form or WhatsApp used for pricing and availability.
Tell us about your project and our team will recommend the right mounting solution for your display or video wall installation.
